[OpenSIPS-Users] I need some info while setiing sethostport on opensips config .

[Sasmita Panda]

Thank you . I will try this .

*Thanks & Regards*
*Sasmita Panda*
*Senior Network Testing and Software Engineer*
*3CLogic , ph:07827611765*


On Tue, Aug 6, 2024 at 2:09 PM Bogdan-Andrei Iancu <bogdan at opensips.org>
wrote:

> Hi Sasmita,
>
> Going back to your original idea, with sethostport(). What you need to do
> is :
>
> 1) strip any potential `transport` param from RURI (as it may force TLS)
>     ruri_del_param("transport");
>
> 2) set as outbound socket an UDP one
>     $socket_out = "udp:192.168.0.69:5060";
>
> Regards,
>
> Bogdan-Andrei Iancu
>
> OpenSIPS Founder and Developer
>   https://www.opensips-solutions.com
>   https://www.siphub.com
>
> On 29.07.2024 12:50, Sasmita Panda wrote:
>
> Any suggestions on this ?
>
>
>
> *Thanks & Regards*
> *Sasmita Panda*
> *Senior Network Testing and Software Engineer*
> *3CLogic , ph:07827611765*
>
>
> On Fri, Jul 26, 2024 at 4:55 PM Sasmita Panda <spanda at 3clogic.com> wrote:
>
>> Hi , Thanks for the reply .
>> Rather than configuration change , I have done through  dynamic routing .
>>
>>  In the dr_gateway table I have added socket information
>> *udp:x.x.x.x:5060*
>> mysql> select * from dr_gateways;
>>
>> +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+
>> | id | gwid | type | address                               | strip |
>> pri_prefix | attrs | probe_mode | state | socket                |
>> description |
>>
>> +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+
>> |  1 | gw4  |    3 | fs.3c.com:6080 |     0 | NULL       | NULL  |
>>    0 |     0 | udp:192.168.0.69:5060 | NULL        |
>>
>> +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+
>>
>> I only have a single Invite on a single session on this leg . There is no
>> Re-Invite at all  . Will I need to set record_route_preset on this case as
>> well ?
>>
>> *Thanks & Regards*
>> *Sasmita Panda*
>> *Senior Network Testing and Software Engineer*
>> *3CLogic , ph:07827611765*
>>
>>
>> On Wed, Jul 24, 2024 at 7:06 PM Ben Newlin <Ben.Newlin at genesys.com>
>> wrote:
>>
>>> Sasmita,
>>>
>>>
>>>
>>> You need to be using $socket_out. [1]
>>>
>>>
>>>
>>> By default, OpenSIPS will use the receiving socket as the sending
>>> socket. This means if you receive the message on TLS and do not change
>>> $socket_out then the message will be sent out the TLS socket.
>>>
>>>
>>>
>>> Additionally, unless you are using B2BUA or maybe topology_hiding you
>>> will likely need to “remember” this protocol transition by adding a double
>>> Record-Route [2] to the message. You may also need to change any
>>> “transport” params that exist in the Request-URI and possibly the Contact
>>> header.
>>>
>>>
>>>
>>> [1] https://www.opensips.org/Documentation/Script-CoreVar-3-2#toc86
>>>
>>> [2] https://opensips.org/docs/modules/3.2.x/rr.html
>>>
>>>
>>>
>>> Ben Newlin
>>>
>>>
>>>
>>> *From: *Users <users-bounces at lists.opensips.org> on behalf of Sasmita
>>> Panda <spanda at 3clogic.com>
>>> *Date: *Wednesday, July 24, 2024 at 1:54 AM
>>> *To: *OpenSIPS users mailling list <users at lists.opensips.org>
>>> *Subject: *[OpenSIPS-Users] I need some info while setiing sethostport
>>> on opensips config .
>>>
>>> * EXTERNAL EMAIL - Please use caution with links and attachments *
>>>
>>>
>>> ------------------------------
>>>
>>> Hi All ,
>>>
>>>
>>>
>>> I am using openisp version : 3.2
>>>
>>>
>>>
>>> I have an opensips config on which I was listening on UDP port only and
>>> hence using sethostport to route calls to a particular destination . like
>>> below .
>>>
>>>
>>>
>>>           if(is_from_gw() || ($rp=~"5505"))
>>>                    {
>>>                   sethostport("freeswitch-test.xyz.com:6080");
>>>                    route(inbound);
>>>                     exit;
>>>                    }
>>>
>>>
>>>
>>> Now I have to accept a call on TLS and send that to some other
>>> destination on UDP . I have enabled the tls module and also the dependent
>>> modules like tls_openssl,  tls_mgm .
>>>
>>>
>>>
>>> socket=udp:192.168.0.y:5060
>>> socket=tls:192.168.0.y:5061
>>> socket=tcp:192.168.0.y:5060
>>>
>>>           if(is_from_gw() || ($rp=~"5505"))
>>>                    {
>>>                   sethostport("freeswitch-test.xyz.com:6080");
>>>                    route(inbound);
>>>                     exit;
>>>                    }
>>>
>>>
>>>
>>> This above configuration is not working . I am getting "477 Send Failed "
>>>
>>>
>>>
>>> *Thanks & Regards*
>>>
>>> *Sasmita Panda*
>>>
>>> *Senior Network Testing and Software Engineer*
>>>
>>> *3CLogic , ph:07827611765*
>>> _______________________________________________
>>> Users mailing list
>>> Users at lists.opensips.org
>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>>
>>
> _______________________________________________
> Users mailing listUsers at lists.opensips.orghttp://lists.opensips.org/cgi-bin/mailman/listinfo/users
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.opensips.org/pipermail/users/attachments/20240806/0a17c516/attachment-0001.html>