[OpenSIPS-Users] Need some reference to run opensips-cli commands .

[Sasmita Panda]

Thank you Giovanni.


*Thanks & Regards*
*Sasmita Panda*
*Senior Network Testing and Software Engineer*
*3CLogic , ph:07827611765*


On Tue, Sep 3, 2019 at 1:48 PM Giovanni Maruzzelli <gmaruzz at gmail.com>
wrote:

> Sasmita,
>
> are you sure you try hard enough before writing to M-L?
>
> I never used this command, I tried three times, and found how.
>
> Maybe you don't try enough?
>
> (opensips-cli): mi get_statistics statistics=all
>
>
> -giovanni
>
> On Tue, Sep 3, 2019 at 10:10 AM Sasmita Panda <spanda at 3clogic.com> wrote:
>
>> If I am running this command it giving me below output .
>>
>> (opensips-cli): mi mem_pkg_dump log_level=4 pid=13019
>> "OK"
>>
>> (opensips-cli): mi mem_shm_dump
>> "OK"
>>
>> What should I do with this .  I need the output like how much memory
>> getting used at that time .
>>
>> This is the output through opensipsctl in opensips-1.11 which I was using
>> earlier .
>> [root at sip spanda]# /usr/local/sbin/opensipsctl fifo get_statistics shmem:
>> shmem:total_size = 4294967296
>> shmem:used_size = 5113048
>> shmem:real_used_size = 15605976
>> shmem:max_used_size = 735486296
>> shmem:free_size = 4279361320
>> shmem:fragments = 624271
>>
>> I need such output . How I will get this ?
>>
>> *Thanks & Regards*
>> *Sasmita Panda*
>> *Senior Network Testing and Software Engineer*
>> *3CLogic , ph:07827611765*
>>
>>
>> On Tue, Sep 3, 2019 at 1:29 PM Giovanni Maruzzelli <gmaruzz at gmail.com>
>> wrote:
>>
>>> then for each command, if you press "tab" it will give you what
>>> arguments are needed (if any)
>>>
>>> (opensips-cli): mi mem_pkg_dump
>>> ERROR: command 'mem_pkg_dump' returned: -32602: Invalid params
>>>
>>> (opensips-cli): mi mem_pkg_dump (->TAB)
>>> log_level=  pid=
>>>
>>>
>>> On Tue, Sep 3, 2019 at 9:54 AM Giovanni Maruzzelli <gmaruzz at gmail.com>
>>> wrote:
>>>
>>>> Sasmita,
>>>>
>>>> execute opensips-cli witouth arguments, then, from inside opensips-cli
>>>> shell, type "mi"and enter
>>>>
>>>> You will see available command,
>>>>
>>>> then for each of them, you can see possible arguments
>>>>
>>>> (opensips-cli): mi
>>>> ERROR: module 'mi' expects the following commands: get_statistics,
>>>> list_statistics, reset_statistics, uptime, version, pwd, arg, which, ps,
>>>> kill, log_level, xlog_level, shm_check, cache_store, cache_fetch,
>>>> cache_remove, event_subscribe, events_list, subscribers_list,
>>>> list_tcp_conns, mem_pkg_dump, mem_shm_dump, mem_rpm_dump, reload_routes,
>>>> help, list_blacklists, t_uac_dlg, t_uac_cancel, t_hash, t_reply,
>>>> clusterer_reload, clusterer_set_status, clusterer_list,
>>>> clusterer_list_topology, cluster_send_mi, cluster_broadcast_mi,
>>>> clusterer_list_cap, clusterer_list_shtags, clusterer_shtag_set_active,
>>>> ds_set_state, ds_list, ds_reload, domain_reload, domain_dump, dlg_list,
>>>> dlg_list_ctx, dlg_end_dlg, dlg_db_sync, dlg_restore_db, dlg_cluster_sync,
>>>> profile_get_size, profile_list_dlgs, profile_get_values, list_all_profiles,
>>>> profile_end_dlgs, dlg_push_var, dlg_send_sequential, rtpengine_enable,
>>>> rtpengine_show, rtpengine_reload, teardown, trace, trace_start, trace_stop
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> On Tue, Sep 3, 2019 at 7:17 AM Sasmita Panda <spanda at 3clogic.com>
>>>> wrote:
>>>>
>>>>> Hi All ,
>>>>>
>>>>> Some commands giving proper output but some are giving error . I am
>>>>> not getting any document where its mention how to run these commands .
>>>>>
>>>>> opensips-cli -x mi "get_statistics"
>>>>>
>>>>> *SQLAlchemy version:  1.3.3ERROR: command 'get_statistics' returned:
>>>>> -32602: Invalid params*
>>>>>
>>>>> opensips-cli -x mi "list_statistics"
>>>>>
>>>>> *SQLAlchemy version:  1.3.3ERROR: command 'list_statistics' returned:
>>>>> -32000: Server error*
>>>>>
>>>>>  opensips-cli -x mi "mem_pkg_dump"
>>>>>
>>>>> *SQLAlchemy version:  1.3.3ERROR: command 'mem_pkg_dump' returned:
>>>>> -32602: Invalid params*
>>>>>
>>>>>
>>>>> How I will run these commands ? I need to check the package memory and
>>>>> shared memory getting used while stress testing . Please do help me .
>>>>>
>>>>>
>>>>> *Thanks & Regards*
>>>>> *Sasmita Panda*
>>>>> *Senior Network Testing and Software Engineer*
>>>>> *3CLogic , ph:07827611765*
>>>>> _______________________________________________
>>>>> Users mailing list
>>>>> Users at lists.opensips.org
>>>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>>>>
>>>>
>>>>
>>>> --
>>>> Sincerely,
>>>>
>>>> Giovanni Maruzzelli
>>>> OpenTelecom.IT
>>>> cell: +39 347 266 56 18
>>>>
>>>>
>>>
>>> --
>>> Sincerely,
>>>
>>> Giovanni Maruzzelli
>>> OpenTelecom.IT
>>> cell: +39 347 266 56 18
>>>
>>> _______________________________________________
>>> Users mailing list
>>> Users at lists.opensips.org
>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>>
>>
>
> --
> Sincerely,
>
> Giovanni Maruzzelli
> OpenTelecom.IT
> cell: +39 347 266 56 18
>
> _______________________________________________
> Users mailing list
> Users at lists.opensips.org
> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.opensips.org/pipermail/users/attachments/20190903/812556d6/attachment-0001.html>