[OpenSIPS-Users] dispatcher not doing fail over itself

Satish Patel satish.txt at gmail.com
Fri Sep 19 14:02:08 CEST 2014


1.12 

Sent from my iPhone

On Sep 19, 2014, at 4:29 AM, Bogdan-Andrei Iancu <bogdan at opensips.org> wrote:

> dst is null as there is no pending destination for failover. cnt is 1. 
> 
> Which OpenSIPS revision are you using ? 
> 
> Regards,
>  Bogdan-Andrei Iancu
> OpenSIPS Founder and Developer
> http://www.opensips-solutions.com
> On 17.09.2014 19:04, Satish Patel wrote:
>> I just trying to print $avp(271) $avp(272) and $avp(273)  
>> 
>> I am getting following output, why dst_avp is null ? and cnt_avp should be 2 right?  
>> 
>>  dst_avp = <null> 
>>  grp_avp = 1 
>>  cnt_avp = 0
>> 
>> Notes: I have both Freeswitch instance running on same box but different port, do you think because of that it think it is single host? 
>> 
>> PARTITION:: default
>>         SET:: 1
>>                 URI:: sip:sip.example.com:5061 state=Active
>>                 URI:: sip:sip.example.com:5071 state=Active
>> 
>> 
>> On Wed, Sep 17, 2014 at 11:06 AM,           Satish Patel <satish.txt at gmail.com>           wrote:
>>> Here you go
>>> 
>>> 
>>> 
>>> 
>>> /sbin/opensips[28000]: Sending call to ===> Freeswitch
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: p=0x7f9ed01dd420, flags=0x0000
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011name=<274>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<10>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011val_int=<0>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: p=0x7f9ed01df208, flags=0x0000
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011name=<273>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<9>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011val_int=<1>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: p=0x7f9ed01e6518, flags=0x0002
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011name=<272>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<12>
>>> /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011val_str=< / 0>
>>> /sbin/opensips[28000]: dispatcher: Attempting to dispatch call to sip:182.xx.xx.xxx:5071
>>> /sbin/opensips[28005]: Inside dispatcher failure route
>>> /sbin/opensips[28005]: ds_dispatcher <null> <null> > <null>
>>> /sbin/opensips[28005]: R-DISPATCHER-ROLLOVER:fU4SNHMvcNmnjW19gsSj0g..-S No more gateways in route set
>>> 
>>> 
>>> On Wed, Sep 17, 2014 at 10:25 AM, Bogdan-Andrei Iancu <bogdan at opensips.org> wrote:
>>>> Hi,
>>>> 
>>>> As mentioned, place the avp_print() just after you did the ds_select_dst(), before relaying to the first destination.
>>>> 
>>>> Regards,
>>>> 
>>>> Bogdan-Andrei Iancu
>>>> OpenSIPS Founder and Developer
>>>> http://www.opensips-solutions.com
>>>> 
>>>> On 17.09.2014 14:09, Satish Patel wrote:
>>>>> Confirmed  probing/inactive thing is working,
>>>>> 
>>>>> Now problem is failover not working, ds_next_dst() not able to find next gateway and it says no more gateway available. If you check my script, i am calling failure route and inside it calling ds_next_dst() but you are saying do avp_print() on ds_select_dst() it won't print anything because after failure you are in failure route block.
>>>>> 
>>>>> Please advice if my script has any issue.
>>>>> 
>>>>> Sent from my iPhone
>>>>> 
>>>>> On Sep 17, 2014, at 3:30 AM, Bogdan-Andrei Iancu <bogdan at opensips.org> wrote:
>>>>> 
>>>>>> Hi Satish,
>>>>>> 
>>>>>> Use the "opensipsctl fifo ds_list" to see the status of the gws in realtime . Be sure that once a gw is in non-active state (probing or inactive), it will not be used again for routing. Just take care of doing the ds_next_dst() in order to jump to the next available gw.
>>>>>> 
>>>>>> If you do the avp_print() after ds_select_dst(), you can see how many other gw are prepared to used in case of failover.
>>>>>> 
>>>>>> Regards,
>>>>>> 
>>>>>> Bogdan-Andrei Iancu
>>>>>> OpenSIPS Founder and Developer
>>>>>> http://www.opensips-solutions.com
>>>>>> 
>>>>>> On 16.09.2014 21:02, Satish Patel wrote:
>>>>>>> After doing couple of TEST look like its marking "Probing" for failed gateway but not auto failover to next gateway, i                                 meant call get disconnect and i need to re-initiate call then all call goes to second active gateway..
>>>>>>> 
>>>>>>> I believe it should first mark gateway "Probing" and then fall-back to second gateway automatically instead of call disconnect and i am getting 503 error code on my SIP Phone.
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.opensips.org/pipermail/users/attachments/20140919/100309f9/attachment.htm>


More information about the Users mailing list