[OpenSIPS-Users] Dialog timeout_avp and onreply_route

[Muhammad Shahzad]

Well, i think if you have enabled onreply_avp_mode in TM module then you
can access and change AVP you set in route block in on_reply block. I don't
see any reason why you need to modify opensips source code for this.

http://www.opensips.org/html/docs/modules/1.8.x/tm.html#id292825

Just change value of SST AVP as i mentioned in previous email when you get
final reply from upstream. However make sure onreply_avp_mode is set as
mentioned in about link.

Thank you.


On Wed, Nov 14, 2012 at 5:37 PM, Mariana Arduini <marianarduini at gmail.com>wrote:

> Hi Muhammad!
>
> Thanks for replying.
>
> I looked at SST module and, at least from docs, there is no mention to
> using it for the 200 OK, only for INVITES...
>
> Even so, I think the problem is that the dialog module does not update the
> timeout value for 200 OK. For example, if you want to refresh the timeout
> value when you get an UPDATE message, you have to set the avp configured in
> timeout_avp modparam and then call match_dialog()/loose_route(), because
> either of these functions will actually update the dialog, and setting the
> avp without calling them will take no effect. I guess the same thing is
> happening when I set the avp after receiving the 200 OK.
>
> Any help on what should be changed in OpenSIPS code so that setting the
> avp in onreply_route will take effect on the dialog timeout?
>
> Thanks!
> Mariana
>
>
> On Wed, Nov 14, 2012 at 1:38 PM, Muhammad Shahzad <
> shaheryarkh at googlemail.com> wrote:
>
>> Use SST module,
>>
>> http://www.opensips.org/html/docs/modules/1.8.x/sst.html#id250008
>>
>> Thank you.
>>
>>
>> On Tue, Nov 13, 2012 at 8:25 PM, Mariana Arduini <marianarduini at gmail.com
>> > wrote:
>>
>>> Hello all,
>>>
>>> I know from the docs that dialog module param timeout_avp " ... may be
>>> used only in a request (initial or sequential) context", but we have a
>>> scenario where the UAS should be the session timer refresher, then we can
>>> only set the timeout_avp value when we get the Session-expires header value
>>> in 200 OK.
>>>
>>> May I ask what would be the best approach to this, like modifying
>>> OpenSIPS code to be able to actually set the avp from onreply_route? If
>>> this is the case, can you please guide us on what would need to be changed?
>>>
>>> Thanks in advance,
>>>
>>> Mariana.
>>>
>>> _______________________________________________
>>> Users mailing list
>>> Users at lists.opensips.org
>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>>
>>>
>>
>>
>> --
>> Muhammad Shahzad
>> -----------------------------------
>> CISCO Rich Media Communication Specialist (CRMCS)
>> CISCO Certified Network Associate (CCNA)
>> Cell: +49 176 99 83 10 85
>> MSN: shari_786pk at hotmail.com
>> Email: shaheryarkh at googlemail.com
>>
>> _______________________________________________
>> Users mailing list
>> Users at lists.opensips.org
>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>
>>
>
> _______________________________________________
> Users mailing list
> Users at lists.opensips.org
> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>
>


-- 
Muhammad Shahzad
-----------------------------------
CISCO Rich Media Communication Specialist (CRMCS)
CISCO Certified Network Associate (CCNA)
Cell: +49 176 99 83 10 85
MSN: shari_786pk at hotmail.com
Email: shaheryarkh at googlemail.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.opensips.org/pipermail/users/attachments/20121114/00673fe0/attachment.htm>