[OpenSIPS-Users] Rebooting a Linksys through OpenSIPS

[Matti Zemack]

Hi,

Thanks again Bogdan. Tried that. Still no go. Suppose I'll try to get some help from Linksys people.

/Matti

-----Original Message-----
From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro] 
Sent: den 13 maj 2009 17:46
To: Matti Zemack
Cc: Sergio Gutierrez; users at lists.opensips.org
Subject: Re: [OpenSIPS-Users] Rebooting a Linksys through OpenSIPS

With qop, do :

response=MD5( HA1 ":" nonce ":" nc ":" cnonce ":" qop ":" HA2)

Regards,
Bogdan

Matti Zemack wrote:
>
> Hi again,
>
> Yes, we tried almost that (as we don't receive a cnonce nor 
> nonce-count in the 401 from Linksys, we only get the qop="auth" which 
> actually by the RFC forces us to use your suggested longer response 
> code.).
>
> We did try with an empty cnonce and nonce count= "nc=00000001" (or empty).
>
> Without success.
>
> /Matti
>
> *From:* Sergio Gutierrez [mailto:saguti at gmail.com]
> *Sent:* den 13 maj 2009 17:16
> *To:* Bogdan-Andrei Iancu
> *Cc:* Matti Zemack; users at lists.opensips.org
> *Subject:* Re: [OpenSIPS-Users] Rebooting a Linksys through OpenSIPS
>
> Hi Bogdan.
>
> For our particular need, it looks like we need to send the response in 
> a more complex way:
>
> response = md5(HA1:nonce:nonceCount:clientNonce:qop:ha2)
>
> Could you give us any hint about nonceCount and clientNonce 
> parameters? Documentation is not very clear.
>
> Thanks and regards.
>
> Sergio.
>
> On Wed, May 13, 2009 at 9:38 AM, Bogdan-Andrei Iancu 
> <bogdan at voice-system.ro <mailto:bogdan at voice-system.ro>> wrote:
>
> Hi Matti,
>
> Actually it is SIP auth, so digest auth (RFC 2617)
> Shortly:
> HA1=MD5( auth_usernam ":" realm ":" passwd )
>
> HA2=MD5( method ":" ruri )
>
> response=MD5( HA1 ":" nonce ":" HA2)
>
>
> Regards,
> Bogdan
>
> Matti Zemack wrote:
> > Hi again,
> >
> > First of all; Thanks Bogdan!
> > Your tip works (theoretically) fine.
> > But, I just can't find a way of calculating the PAP2s authentication.
> > Not much seems to be documented.
> > Does anyone have any hints regarding Linksys authentication (for a
> > reboot at least).
> >
> > I've tried calculating using
> > http://en.wikipedia.org/wiki/Digest_access_authentication , and
> > basically sticking to RFC2069, as I don't believe I have have nonceCount
> > & clientNonce.
> > By the way; how should the digestURI look? (I've tried the combinations
> > that came to my mind...)
> >
> > Best regards,
> > Matti Zemack, Stockholm, Sweden
> >
> > -----Original Message-----
> > From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro 
> <mailto:bogdan at voice-system.ro>]
> > Sent: den 12 maj 2009 10:33
> > To: Matti Zemack
> > Cc: users at lists.opensips.org <mailto:users at lists.opensips.org>
> > Subject: Re: [OpenSIPS-Users] Rebooting a Linksys through OpenSIPS
> >
> > Hi Matti,
> >
> > Well, it should be possible - you do a 2 steps interaction with the
> > Linkys :
> > - first send the NOTIFY via the t_uac_dlg MI command and get from the
> > result the auth challenge (in the MI command response you do have access
> >
> > to the SIP reply)
> > - generate a new NOTIFY request including the Authorize header
> > calculated based on the received challenge.
> >
> > Regards,
> > Bogdan
> >
> > Matti Zemack wrote:
> >
> >> Hi all,
> >>
> >> I'm still dipping my toes in deep waters with OpenSips 1.5...
> >>
> >> And I've come across a small problem. I would like to reboot Linksys
> >> ATA (PAP2 etc...) using OpenSIPS.
> >>
> >> Can this maybe be done?
> >>
> >> Basically I use XML-RPC FIFO to send the SIP command. The problem is
> >> that Linksys replies with 401 challenge. Can I, or is it at all
> >> possible to reply to this challenge using OpenSIPS?
> >>
> >>
> >
> >
> >
>
>
> _______________________________________________
> Users mailing list
> Users at lists.opensips.org <mailto:Users at lists.opensips.org>
> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>
>
>
>
> -- 
> Sergio Gutiérrez
>